The new 850 HD Pro was created following the request to build a RIB with special features: plenty of space on board; possibility of fitting out according to the different needs of professional owners; great sturdiness of construction; and finally, but not least, an unequivocally Marlin RIB with its characteristic unmistakable lines, attention to detail, and great quality and functionality. Thus a professional RIB was born, where particular attention was paid to the design of the structures and spaces on board where it is possible to stow equipment and equipment, without hindering the user.

At the extreme bow there is a stainless steel big bollard supported by a pulpit, the anchor locker with a new design already prepared for mounting the electric winch under the top of the locker; the anchor, which emerges from the extreme bow wheel just below the tubules, remains protected by the latter, allowing you to approach the dock or other boats without fear.

In addition to a very large locker that extends even under the walking surface, there is a locker on the floor where you can easily mount a water tank or equip at will.The locker below the stern area, unlike almost all of these RIBS, is accessible; this allows, in the fitting phase, to mount systems and batteries in this area, but also, during the molding of the hull, to join the deck to the hull from the inside: a fundamental guarantee of resistance to the very high stresses to which these types of boats are subjected.

The floor, made in fiberglass sandwich and high density Termanto, has a length of 5 meters and a width of 2 where it will be possible to decide the layout of the various settings.

The driving console with a limited longitudinal dimension, but capable of protecting two pilots and accommodating any electronic equipment in the large panel.

The tubes, built with 1670 Dtex fabric and reinforced with non-slip material, is developed on two levels, low aft to lean on the surface and give the boat greater stability in all conditions, high in the bow, and not to interfere with the motion wave during navigation, both to build high internal walls that give crew absolute protection and safety.

This particular profile, designed and patented by Marlin Boat in 1993, was adopted for all the yard’s models, making it a real trademark.

The strength of the hull is guaranteed by coupling three different moldings: the deck, the reinforcement “spider” and the hull which are firmly joined together forming a monolith of exceptional resistance to stress.

The resin processes are performed using the highest quality materials, such as Neopentyl Gel Coat and Vinylester Resin to avoid osmosis phenomena.

The new Marlin 850 HD Pro will also be presented in a superequipped GT version, with bow sundeck and rear sofa, hard top and other exclusive accessories, especially designed for recreational use, which is also well suited for use as a luxury tender, where the exceptional characteristics of sturdiness and construction will be maintained.

Marlin Boat - 850 HD Pro GT


Scorri verso il basso


Design category
Homologation lenght
cm 850
Overall lenght
cm 850
Overall width
cm 318
Internal length
cm 775
Internal width
cm 194
Tubular diameter
cm 62
Weight without motors
kg 1450*
Capacity of people
nr. 18
Maximum power CV
Stern height
nr. 7
Fuel tank capacity
lt. 420
Water tank capacity
lt. 80
Tube material
Neoprene-Hypalon 1600 gr/m²
Vetroresina - tripla stampata
Progetti e brevetti Marlin Boat


2 stainless steel 300 mm stern cleats
3 external stainless steel eyebolts
4 lifting eyebolts
Inox bow bollard with pulpit and pass-bys
Reinforced hull
20 mm perimeter handrail rope
Two-seat guide console with windscreen, stainless steel handrail, drawer and front door
Front locker for anchor and chain
Floor-mounted locker
Front locker for stowage
Rear locker
Electric inflator and pressure gauge
Electrical system with 8 users panel
Kit u-shaped stern sofa with cushions
Kit bow sunbathing with cushions
Repair kit
Floor re-flex foam kit
Lifting strops kit with shackles
Lights off
Automatic bilge pump
Stainless steel ladder with handrail
Two-seat guide seat with anatomical fiberglass and stainless steel cushion
Water tank 80 lt with shower and pump
420 liter stainless steel tank
Steering and seat covers
1600 D Tex heavy fabric tubular with non-slip reinforcements
Anchor windlass with chain and stainless steel anchor 7,5kg
GRP: White
Tubes: artic grey
Cushions: grey
Water skiing towing pole
Front lockers closure
Bathroom console with chemical toilet and porthole
Bow walking surface
Bow thruster
Stern underwater blue led lights
Stainless steel and fybreglass hard top with led navigation lights
Cockpit and platform complete lighting blue led lights
Floor synthetic teak 6 mm kit
Stern bathing platforms with stainless steel ladder
Stainless steel rollbar with lights
Stainless steel rollbar with lights and extensible bimini
Seat with 50 lt fridge and sink
Bow console seat
Table with removable pedestal and pillow
Stern bimini for hard top with carbon elastic poles
Stainless steel 4 arch bimini
Mooring cover
Hydraulic steering tilt single cylinder 350/700 hp
Tubes color variant
Cushions color variant
Grey fiberglass ral 7046 color variant
Electronic equipment
Scorri verso il basso